Fresno Performance?!?!?!?

[zimmerc]

Has any one heard anything good or bad about this place? I need some work done but I want to make sure they will do more good than bad. Any comments appreciated!:questionmark:

 

[Foxman]

owner wont post... so no need for me to

must be happy with the work

 

[Foxman]

there is always two sides to the story... i would love to hear theirs

 

[zimmerc]

Yeah. Im apprehensive of leaving my car anywhere and I just have to do my research

 

[Feared]

i know there are 2 guys from that shop that are on this board, and i know atleast one of them had a hand in the car. THey should chime on this.

What work do you need done?? Maybee they can get you a quote.

 

[Foxman]

elky406 hasn't been on this forum since 8/20/20009

 

[zimmerc]

Im looking for rearend gears and a nitrous dyno tune.

 

[Ichiduo]

i've only had my mach tuned by nate... no actual "work" as far as modifying parts were done. nate even told me to come by if there are any problems with the tune and he'd work them out.

can't speak for their work (since none was done on my mach), but their tuning is awesome.

 

[Renegade]

i had subframes installed by them, the weld job was nothing special just common welding, but when i got under the car the other day the the nuts for the passenger side one were gone, my guess is no locktite

 

[Foxman]

^^^ i thought you and your dad were going to make your own?

 

[Renegade]

we are making our own for the fox, but the guys at spintech made me one hell of a deal on theirs so i took the easy route

 

[Foxman]

we are making our own for the fox, but the guys at spintech made me one hell of a deal on theirs so i took the easy route

morgan and slates is your friend LOL

 

[Foxman]

i had subframes installed by them, the weld job was nothing special just common welding, but when i got under the car the other day the the nuts for the passenger side one were gone, my guess is no locktite

how much for install?

 

[Renegade]

idk id have to search for my invoice, i have a family friend coming out soon to check out everything he has to do sheet metal wise for the fox, thats gunna save me a lot of time and a lot of cuts lol

 

[Feared]

I know they cut off a good set of headers, to were they cant be used agian off scotts car... mounted his rear end crooked and charged him for a alingment, then when we found out the rear was crooked they told him he need to pay for a 4 wheel alingment.....and he payed somewere around 15k+...... for a t56, tubluar K member and solid axle swap... oh and full exhaust and coil overs

these are facts... take them as good or bad....

didnt they have that thing for 6-7 months, and it still wasnt ready when he got back from deployement??

 

[Feared]

this is what 15k gets you at fresno performance. They gave his car back to him w/o an alignment, and not adjusting the rear end properly.. WTF..



the right side sticks out more than the left.

 

[Feared]

right side.

left side.

Look at the exhaust.. NOT EVEN LINED UP!

you can tell the axle is croked in the car.

 

[Foxman]

owner wont post... so no need for me to

must be happy with the work

 

[Feared]

Now granted this can be fixed, but why would it need fixed or adjusted when the car JUST CAME OUT OF THE SHOP!>? what kind of shop gives this back to the person and says the car is done?

I wouldnt take that down the track. THats some bad work by these guys.

 

[Foxman]

owner wont post... so no need for me to

must be happy with the work