• Hello there guest and welcome to our forum!
    To gain full access you must Register. Registration is free and it takes only a few moments to complete.
    Already a member? Login here then!

my 03 cobra.enjoy

E

elky406

Well-Known Member
hpim0932m.jpg

hpim0933.jpg

hpim0934.jpg

hpim0935.jpg

hpim0936.jpg

hpim0937.jpg

hpim0938.jpg

img4544copy.jpg

img4641copy.jpg


i have more but this is what im in the mood to look for lol.


the build consist of

96 cobra block,stock 03 cobra crank and rods,manley pistons,ported heads,custom ground cams,manley valves and springs,ti retainers,whipple chrusher 3.4 24 lbs of boost,stock lower 3.5 upper pulley,medco 100mm idlers.80 lbs injectors,return style fuel system with sumped tank and dash 10 feed line,4500 art car non lock up converter,lentech 4r70w trans with a brake,max motor sports k member a arms d and d coil overs 175lbs frt springs.hpm mega bite jr lowers with the upr sperical uppers,8.8 with 33 spline carrier and axles,t/a girdle cover welded tubes,in house sub frame connectors in house 3 inch mandrel exhaust with dynomax mufflers.Engine was built in house and trans was freshend in house,In house built rear end and in house tuned.Also has a single wet fogger nozzle.CAr is 3600lbs and makes 850whp on 24lbs and now a 75 shot48 nos jet.CAr has gone a best of 9.60 at 147 on less power with 2 tenths left in it,as it wasnt a clean pass.best 60ft on boost 1.43,best on nitrous boost combo 1.40.
 
I

Ichiduo

Guest
help you out a bit there:

[ame="http://www.youtube.com/watch?v=Y0P4GUrXRlY"]YouTube - Nate's Cobra[/ame]

oh yeah, nice cobra. :)
 
Shane361

Shane361

Well-Known Member
Man, that is a very beautiful car! So you have metco idlers and not the great looking ones in the pictures rite? Pretty sure they would not hold to your HP cause at 481rwtq I shreaded mine.-Shane
307b.jpg
 
M

Mustangcwo

Guest
The car is a beast. Thats almost the exact combo going into wicked fox over the next month. I hope our fox body can handle all that torque!!!! I have new found high hopes....THANKS.
 
E

elky406

Well-Known Member
Yes i went away from the stock pulleys,broke like 10 of them lol.

where and when is the mustang vs the world deal?

I will have to get some pics of the sick rear seat delete we did and my new 8 gallon water storage tank in the trunk for the heat exchanger.CAn you say 10 degree inlet temps while on the nitrous and 50 lbs of ice in the trunk.
 
E

elky406

Well-Known Member
the vids where of the car in boost only,im so close to 9.90s on boost.It has it in it for sure just gotta work on a few things,mainly spark blow out,as you can hear badly in the last run,car left hard,actually spun pretty badly but still went wheels up.
 
E

elky406

Well-Known Member
[ame="http://www.youtube.com/watch?v=faW9luFmmHI&feature=channel_page"]YouTube - Elky406 at Sacramento Raceway[/ame]

this is my elco when it was a all iron 489 big block at 3900lbs,4 mufflers on pump gas.Lifted off the 300 shot at half track as seen by the mph,car went 10.0s to 10.20s at 133 on motor and went a best of .27 at 147 on 400 tuneup.Not bad for a under 10 to 1 all iron heavy old farm truck.

Best 60ft 1.31 300 shot

best all motor 60ft 1.41
 
E

elky406

Well-Known Member
[ame="http://www.youtube.com/watch?v=mZeJlaPeZrw&feature=channel_page"]YouTube - Nate's 03 Cobra[/ame]
this is my cobra with stock motor,4r70w 18 psi on the 2.3 and a 75 shot,full wieght of 3800lbs,drove it to and from the track over 250 miles on pump piss.
 
S

sdsubzero4

Spring Valley, CA
4R70W.....I have some hope after reading the magazine article Emilio gave me and seeing the video of this Cobra. I have hopes! LOL!
 
You must log in or register to reply here.
Top